D G V S - 3 9 1 1 0 ( 0 9 Y ) IBM Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders | | | Capacity form/unform 9110/ MB Heads 12| | | Seek time / track 6.5/ ms Sector/track | | | Controller SCSI3 SI/WI/ULT2/FAS Precompensation Cache/Buffer 1000 KB SEGMENTED Landing Zone Data transfer rate 16.000 MB/S int Bytes/Sector 512 20.000 MB/S ext SYNC Recording method EPRML operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 50 | -40 65 Power: sleep W Humidity % 5 90 | 5 95 standby W Altitude km -0.300 3.000| -0.300 12.000 idle 16.5 W Shock g 10 | 135 seek W Rotation RPM 10020 read/write 19.3 W Acoustic dBA spin-up W ECC Bit SMART MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** IBM DGVS-09 ULTRASTAR 9ZX +-----------------------------------------------------+ | | | | | | | | |++---------SCSI-----------------+-Aux.---+-Power---++| ||| +------------------------1-+ |+-----1+|+-------+||| ||| |\::::::::::::::::::::::::/| ||::::::|||XXXXXXX|||| ||| +------------------------35+ |+-----2+|+-------+||| ||+------------------------------+Connect.+-4-3-2-1-+|| ++ ++ ********************************************************************** J U M P E R S ********************************************************************** IBM DGVS-09U/09Y ULTRASTAR 9ZX Jumper Setting -------------- Termination Power Enable +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ +--+--+ |01|03|05|07|xx|11|13|15|17|19|21|23|25|27|29|31| | | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |01|02| |02|04|06|08|10|12|14|16|18|20|22|24|26|28|30|32| | | | +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ +--+--+ *NOTE: PINS 1 AND 2 DO NOT EXIST IN 50-PIN MODELS! Pin| Description ---+--------------------------------------------------------- 01 | Bit 3 (MSB) (Do not exist in 50-pin models)--+ 03 | Bit 2 --+ Address 05 | Bit 1 --+ Jumpers 07 | Bit 0 (LSB) --+ 09 | Blank Polarity 10 | Unused 11 | Auto Start 13 | Ground 14 | Enable Active Termination 15 | -Master Sync 16 | -Slave Sync 17 | External Activity LED 18 | +5V 19 | Write Protect 21 | Auto Start Delay 23 | Option Block Mode 25 | Disable Sync Negotiations 27 | Disable SCSI Parity 29 | Disable Unit Attention 31 | Disable F/W Negotations 68/80-Pin SCSI ID ----------------- +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | Bit 3 | Bit 2 | Bit 1 | Bit 0 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ NOTE For attachment to a Macintosh, place jumpers on pins 29 & 30 to Disable Unit Attention and pins 11 & 12 for Auto Start. Auto Start (& Delay) Pins ------------------------- The Auto Start and Auto Start Delay pins control when and how the drive can spin up and come ready. When configured for Auto-Startup, the motor spins up after power is applied without the need of a SCSI Start Unit command. For no Auto-Start, a SCSI Start Unit command is required to make the drive spin and be ready for media access operations. When in Auto-Start mode, the drive will delay it's start time by a period of time multiplied by it's own SCSI address. Write Protect Pins ------------------ If the Write Protect pin is jumpered to ground the drive will prohibit SCSI commands that alter the customer data area portion of the media from being performed. The state of this pin is monitored on a per command basis. Disable Sync. Negotiation Pins ------------------------------- If a Disable Target Initiated Synchronous Negotiation pin is grounded then an Initiator is required to start a negotiation handshake if Synchronous and/or Wide (Double Byte) SCSI transfers are desired. Disable SCSI Parity Pins ------------------------ Grounding this pin will disable SCSI Parity checking. Disable Unit Attention Pins --------------------------- Grounding this pin will disable the drive from building Unit Attention Sense information for commands immediately following a Power On Reset (POR) or SCSI Bus Reset. Any pending Unit Attention conditions will also be cleared at POR or SCSI Reset times. ********************************************************************** I N S T A L L ********************************************************************** -ANY DIREC. Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). ********************************************************************** F E A T U R E S ********************************************************************** IBM DGVS-09U/Y ULTRASTAR 9ZX Attaching the Drive ------------------- 1. Turn off the Computer, unplug the power cord and open the case. 2. The DGVS drive requires Active Termination on both ends of the SCSI cable (the SCSI controller normally provides internal termination for one end of the cable). If the DGVS drive is the only device on the SCSI cable, attach it to the end of the cable furthest from the controller and enable termination by placing a jumper across pins 13 and 14 of the Option Jumper Block. If the drive is attached to a cable that contains other devices and the new drive is not attached to the end of the cable, the jumper across pins 13 and 14 must be removed and Active Termination must be supplied by the device at the end of the cable. 3. Select the other option jumpers as required by your computer. 4. Attach the power connector.