C F P - 4 2 0 7 W V C A Y M A N A V CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 4016| | | Capacity form/unform 4294/ MB Heads 20| | | Seek time / track 8.5/ 2.0 ms Sector/track | | | Controller SCSI2 SI/WI/FAS/AV Precompensation Cache/Buffer 512 KB Landing Zone Data transfer rate 6.700 MB/S int Bytes/Sector 512 20.000 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 5 95 | 5 95 standby W Altitude km -0.061 3.048| 12.192 idle 12.8 W Shock g 5 | 50 seek 14.3 W Rotation RPM 7200 read/write 13.2 W Acoustic dBA spin-up W ECC Bit MTBF h 1000000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CFP-4207W QUICK REFERENCE GUIDE 12/94 REV. C +---------------------------------------------------------++---+ | +-J1 ++++ ||XX J2 | | | |||| ||XX |68 | | | |||| ||XX |Pin | | | |||| ||XX | | +-+ |||| ||XX | | *+*+ ||XX | | E8++ ||XX | | ++ ||XX | | (Fuse)F1xx ||XX1| | J3 ++ ||+-+| | +-+ SS ++++++++ || ||| |J5 | | | LED ++++++++ || ||| || | | | E1 ****** E7 || ||| || | +-+ || ||+-1| | *+ ||xx | ++ ||XX J4 ++LED ||XX Power +---------------------------------------------------------++--1+ ********************************************************************** J U M P E R S ********************************************************************** CONNER CFP-4207W QUICK REFERENCE 12/1994, REV. C Jumper Setting ============== Setting the SCSI Bus Address ---------------------------- There are four jumpers available for configuration of the SCSI ID: E1, E2, E3 and E4. Setting the SCSI ID ------------------- +-------+----------+----------+----------+----------+ |SCSI ID| E1 | E2 | E3 | E4 | +-------+----------+----------+----------+----------+ | 0 |OUT/OPEN |OUT/OPEN |OUT/OPEN |OUT/OPEN | +-------+----------+----------+----------+----------+ | 1 |IN /GROUND|OUT/OPEN |OUT/OPEN |OUT/OPEN | +-------+----------+----------+----------+----------+ | 2 |OUT/OPEN |IN /GROUND|OUT/OPEN |OUT/OPEN | +-------+----------+----------+----------+----------+ | 3 |IN /GROUND|IN /GROUND|OUT/OPEN |OUT/OPEN | +-------+----------+----------+----------+----------+ | 4 |OUT/OPEN |OUT/OPEN |IN /GROUND|OUT/OPEN | +-------+----------+----------+----------+----------+ | 5 |IN /GROUND|OUT/OPEN |IN /GROUND|OUT/OPEN | +-------+----------+----------+----------+----------+ | 6 |OUT/OPEN |IN /GROUND|IN /GROUND|OUT/OPEN | +-------+----------+----------+----------+----------+ | 7 |IN /GROUND|IN /GROUND|IN /GROUND|OUT/OPEN | +-------+----------+----------+----------+----------+ | 8 |OUT/OPEN |OUT/OPEN |OUT/OPEN |IN /GROUND| +-------+----------+----------+----------+----------+ | 9 |IN /GROUND|OUT/OPEN |OUT/OPEN |IN /GROUND| +-------+----------+----------+----------+----------+ | 10 |OUT/OPEN |IN /GROUND|OUT/OPEN |IN /GROUND| +-------+----------+----------+----------+----------+ | 11 |IN /GROUND|IN /GROUND|OUT/OPEN |IN /GROUND| +-------+----------+----------+----------+----------+ | 12 |OUT/OPEN |OUT/OPEN |IN /GROUND|IN /GROUND| +-------+----------+----------+----------+----------+ | 13 |IN /GROUND|OUT/OPEN |IN /GROUND|IN /GROUND| +-------+----------+----------+----------+----------+ | 14 |OUT/OPEN |IN /GROUND|IN /GROUND|IN /GROUND| +-------+----------+----------+----------+----------+ | 15 |IN /GROUND|IN /GROUND|IN /GROUND|IN /GROUND| +-------+----------+----------+----------+----------+ Open means open circuit or high impedance. Ground means TTL logic low or logic ground. Disabling Spin-Up at Power On ----------------------------- A jumper in the E5 location, disables spin up after power-on for applications where spin up sequencing is necessary. Disabling spin up on application of power can also be enabled by setting the DSPN bit in MODE SELECT page 00H (Operating Parameters). The Host must issue a Start UNIT command to cause the drive to spin up. +---------+------+---------------------+ | E5 | DSPN | Result | +---------+------+---------------------+ | IN | 0 | Spin Disabled | +---------+------+---------------------+ | IN | 1 | Spin Disabled | +---------+------+---------------------+ | OUT | 0 | Spin up on Power On | +---------+------+---------------------+ | OUT | 1 | Spin Disabled | +---------+------+---------------------+ Delaying Spin Up at Power On ---------------------------- A jumper in the E6 location, delays spin up on power-up by the value of the drive's SCSI ID multiplied by 4 seconds (i.e. SCSI ID 4 will delay 16 seconds). Delaying spin up on application of power can also be enabled by setting the SDLY bit in MODE SELECT page 00H (Operating Parameters.) +---------+------+---------------------+ | E6 | SDLY | Result | +---------+------+---------------------+ | IN | 0 | Spin Delayed | +---------+------+---------------------+ | IN | 1 | Spin Delayed | +---------+------+---------------------+ | OUT | 0 | Spin up on Power On | +---------+------+---------------------+ | OUT | 1 | Spin Delayed | +---------+------+---------------------+ Disabling the SCSI Bus Parity ----------------------------- SCSI parity is always enabled in both directions, unless the E7 Parity disable jumper is installed. Installing the jumper will cause the drive to ignore SCSI bus Parity In but it will continue to generate SCSI bus parity out. Disabling SCSI Bus Terminator Power (TERMPWR) --------------------------------------------- Power to the on-board terminators is provided by the higher of the voltage supplied at Pin #17, 18, 51 & 52, J2 or the voltage level at the 5 Volt power input to the drive minus one diode drop. Termination Power to external terminators can be supplied by the drive through Pin #17, 18, 51 & 52, J2. The TERMPWR line can be disconnected from the drive by removing Jumper E8. Jumper E8 | Result ----------+---------------------------------------------------- IN | TERMPWR (J2, Pin #17, 18, 51 & 52) connected to the | drive's internal termination power. ----------+---------------------------------------------------- OUT | TERMPWR (J2, Pin #17, 18, 51 & 52) open circuit. Setting the Bus Termination --------------------------- Remove the SCSI Terminators in all but the last drive in the chain.