S T 3 4 5 7 1 N B A R R A C U D A SEAGATE Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 5178| | | Capacity form/unform 4550/ MB Heads 10| | | Seek time / track 10.0/ 2.0 ms Sector/track | | | Controller SCSI3 SI/ULTRA Precompensation Cache/Buffer 512 KB READ-AHEAD Landing Zone Data transfer rate 10.000 MB/S int Bytes/Sector 512 20.000 MB/S ext SYNC Recording method PRML 0/4/4,ZBR operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle 10.0 W Shock g | seek W Rotation RPM 7200 read/write W Acoustic dBA spin-up W ECC Bit MTBF h 1000000 Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** J U M P E R S ********************************************************************** SEAGATE ST32271/34571-N/ND BARRACUDA 4LP JUMPER SETTING Jumper Setting ============== REAR VIEW 50 pin I/O Cable Connection | J1+------------------------1+ /---------\ TOP (HDA) ---+:::::::::::::::::::::::::+-+ X X X X +--- +-------------------------+ +-5-G-G-12+ BOTTOM V R R V O U U U N N D D SIDE VIEW BACK +-+ J2 12345678 TOP (HDA) FRONT OF J1+---------------------PWA------------------------ OF DRIVE +-+ :::::::: BOTTOM DRIVE |||||||| +Terminator Power +||||||+ Enable T-Res (N model only) ++Terminator Power -+||||+- Start Delay (12 secs * ID) | RESERVED --+||+-- Motor Start | Parity Disable ---++--- Write Protect | | | +--------------------------------+ +-+ Termination Power-source Table | +--------------------------------+-------------+ |-----....-----....-----PWA edge----- | | | | 1 2 1 2 1 2 | | A Drive Supplies Bus | | X o o X o o B Drive Supplies Own | | x o o x xxx C Bus Supplies Drive | | A B C | +---------Default------------------------------+ Note: ND drives do not have internal terminators or any other way of adding internal terminators to the drive; use external active termination if required. FRONT VIEW +--+RESERVED! Shipped with cover installed. | +Do not remove. Do not install jumpers TOP (HDA) ++---+-----1+ -PWA--------------------+::::|::::::+---- * BOTTOM +----+123456+ | J6 |||||| LED -+ |||||| Remote LED +||||+ ID 1 (pin-11 +5V) |||+- ID 2 RESERVED -+++-- ID 4 SCSI ID ------- +----------+-----------------------+ | SCSI ID | Jumpers | | | ID4 | ID2 | ID1 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ ********************************************************************** I N S T A L L ********************************************************************** -ANY DIREC. Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions).